Multiphysics is defined as the coupled processes or systems involving more than one simultaneously occurring physical field and the studies of and knowledge about these processes and systems.As an interdisciplinary study area, multiphysics spans over many science and engineering disciplines. Multiphysics is a practice built on mathematics, physics, application, and numerical analysis. The mathematics involved usually contains partial differential equations and tensor analysis.
The physics refers to common types of physical processes, e.g., heat transfer (thermo-), pore water movement (hydro-), concentration field (concentro or diffuso/convecto/advecto), stress and strain (mechano-), dynamics (dyno-), chemical reactions (chemo- or chemico-), electrostatics (electro-), neutronics (neutro-), and magnetostatics (magneto-).
Hi everyone, Has anyone tried to model Radiative Transfer equation on comsol? I am stuck at defining the integral term which includes scattering. Also , how do i make my functions have 3 variable dependence as RTE has dependence on position, time and direction vector
Hi. I am studying the effect of plasmonic nanoparticles on solar cells. Is there a way to calculate absorption efficiency in different layers of tandem solar cells in COMSOL Multiphysics.
Hi All
How can i simulate Graphene in Comsol? I am using semiconductor module .
I s it correct to use Drude model?
Drude model is in RF module but my simulation should be run in semiconductor module.
How about Kubo formula?(for optics application or no?)
I know these calculations in thermodynamics can be done by hand or a simple calculator but I wonder if some programs do these calculations. These programs might be called multiphysics programs. An example of a calculation - select piston-cylinder arrangement.
-enter initial...
Hi, I use the software COMSOL Multiphysics.
I would like to get the solution outputs of the mathematical problem that I run.
Specificaly I would like to get pressure and velocity (according to time) of the
flow that is flowing through a mean.
Do I have this ability in comsol multyphysics?
How...
I have come across the paper attached in which a 1D fluid piston is modeled.
I have question on the boundary conditions (BCs) of the system. Essentially, the problem consists of a fluid chamber in contact with a spring (a mass -spring system). ALE is used to move the mesh. I am not certain...
Hi all,
First time poster here, and currently looking for some good advice. I’m about to finish my master studies in June and therefore I’m looking for advice. I’m searching for a university that has a renowned department/study group in a specific field of study. I hope to join that study...
hi
who can help me with my problem in comsol multiphysics? i want to calculate a schrodinger equation for a spherical quantum dot under applied magnetic field, who can help me? anyone here have the program doing this? help me if you can. i don't know if there is another program for compute...
Good morning,
I was wondering if you could help me solve a problem with a poroelastic model with COMSOL Multiphysics.
It is a very simple model preliminary to my real study to understand the role of Poisson's ratio on the simulation, keeping all other parameters constant.
The model is a...
Hi i am performing a multiphysics simulation in which i am importing results of Electric-Thermal domain into Transient Structural domain in Ansys Workbench 14.5. As the simulation time is 5 hrs and given that i have to perform 20 case studies , so i want to know is their a way around in Ansys...
Good Day,
I am working on a problem in which i am coupling "Thermal-Electric" physics with "Transient Structural" in Ansys workbench V 14.5. I am supplying electric energy(Voltage) to a structure which gets heats up due to Joule Thomson effect, and then i connect it's "Solution" to "Setup" tab...
Hi friends.
I am so new with Comsol software to design something but I wonder, if it is possible to desing a bending magnet (dipole) and simulate the motions of electrons ? I really would like to do this. Please give me a hand,help me to handle and try to do one together.
Best.
Hello, I'm a telecomunications student. I am new here and I have some doubts with Comsol software.
This is the first time I use Comsol, and I want to simulate the comunication between two antennas inside a tank with 2 different matterial, air and corn(wheat). I have the electric constants of...
Hello everyone!
I'm a new entry in thi forum and I need some help with Comsol multiphysics.
I'm creating a model of tsunami waves propagation in a defined domain using the PDE interface.
I ve not problems in stationary case, but when I try in time dependent case Comsol give me the error...
Hi,
I am using Comsol Multiphysics to model a magnetic plug surounded by water in a tube.
The plug interacts with a magnet and a force is induced.
Since I am using the ALE moving mesh option, i have defined the boundaries of the geometry to move with the velocity of the plug.
This...
Dear Friends !
I would really need Your help. I am currently simulating the temporal development of an interface between liquid and gas, by using Comsol Multiphysics.
The problem can be simplified in terms of a rotating central liquid pick up (a small rotating cylinder endowed with an...
Hi
I'm trying to get comsol multiphysics to first define an inline
function with 1 variable and 4 parameters, and then run fzero on that
same function. I can do it with two parameters, but no moore.
This works:
clear
myfun=inline('exp(y).*cos(x)+z', 'x', 'y', 'z');
x1 =...
Hello everyone,
Does anybody use Comsol multiphysics here?
I am trying to model the electric double layer. If you have experience, please share with me.
I want to solve a system of differential equations in comsol multiphysics.
So far I have not figured out how to enter a 2nd pde in addition to the existing pde.
Is this possible, and how?
I have just started to work on FEMLAB.I am using at the moment the PDE modes-Weak forms to solve flow over topography using the lubrication equation. I have implemented the lubrication equations into the subsomain settings and set the boundary conditions but i do get wrong results. Does anyone...
I'm working on solving coupled PDEs (mass diffusion - heat transfer - continuum mechanics) in problems where the solution domain changes depending on the solution (call it an intrinsic coupling if you will). This happens either due to addition of material to the domain or damage of the domain...