Solve Angle Between Light Rays After Prism Refraction - Help (with prism)

  • Thread starter Thread starter shingetsunohimitsu
  • Start date Start date
  • Tags Tags
    Prism
AI Thread Summary
The discussion centers on calculating the angle between two parallel light rays after they pass through a prism with a refractive index of 1.48 and an entry angle of 30 degrees. Participants express confusion about the geometry of the situation, particularly regarding the rays' entry points and whether they strike the same internal surfaces of the prism. There is a consensus that if the rays are parallel upon entering and interact with the same walls, they should remain parallel after exiting. Additionally, a warning is raised about the incorrect use of arcsin with values greater than 1, emphasizing the need for clarity in the calculations. Overall, clearer descriptions or diagrams of the prism and ray paths are requested to facilitate understanding.
shingetsunohimitsu
Messages
7
Reaction score
0
Help

34-31. The prism of the figure has a refractive index of 1.48, and the angles A are 30.0°. Two light rays m and n are parallel as they enter the prism. What is the angle between them after they emerge?
I. Set the hypotenuse of the small triangle to the left at 10cm. Gives you a triangle which is 5^2+8.66^2=10^2
II. The angle should be arccos(5/10)=60.0°
III. The angle of refraction should be arcsin(1.281)
The angle they make with the base of the prism should be arcsin(1.281)+30.0°, In which case the angle they make towards each other is as much 2(arcsin(1.281)+30.0°)


Now, the answer, I'm sure is completely off the hooks.

I'm new around, I don't have a university degree, only what's equivalent to basic high school maths and a burning passion for physics. My dabbling in the arts are meagre, and I want to ask pardon my stupid questions before anyone gets the chance to demand a pardon from me. There you go.
In all my humbleness
/Shingetsu
 
Physics news on Phys.org
I'm having a hard time picturing the situation. Do the two rays enter the hypotenuse of the triangle with an angle of incidence of 30 degrees? AFter they enter the prism, which internal side do they hit? Do both rays hit the same side internally?

If the two rays are parallel when coming in, and they have do not have different index of refraction, and they hit the same walls of the prism, they should emerge parallel to each other.

And you can't have an arcsin of a number greater than 1.00, so figure out what you meant by that.
 
If you can attach a figure, that will help us understand what's going on. As chi meson said, it's not clear why the emergent rays should not be parallel too - unless they don't go in the same side.

If you have absolutely no means of providing a figure, try describing the prism and the ray directions more clearly.
 
I multiplied the values first without the error limit. Got 19.38. rounded it off to 2 significant figures since the given data has 2 significant figures. So = 19. For error I used the above formula. It comes out about 1.48. Now my question is. Should I write the answer as 19±1.5 (rounding 1.48 to 2 significant figures) OR should I write it as 19±1. So in short, should the error have same number of significant figures as the mean value or should it have the same number of decimal places as...
Thread 'Minimum mass of a block'
Here we know that if block B is going to move up or just be at the verge of moving up ##Mg \sin \theta ## will act downwards and maximum static friction will act downwards ## \mu Mg \cos \theta ## Now what im confused by is how will we know " how quickly" block B reaches its maximum static friction value without any numbers, the suggested solution says that when block A is at its maximum extension, then block B will start to move up but with a certain set of values couldn't block A reach...
Thread 'Calculation of Tensile Forces in Piston-Type Water-Lifting Devices at Elevated Locations'
Figure 1 Overall Structure Diagram Figure 2: Top view of the piston when it is cylindrical A circular opening is created at a height of 5 meters above the water surface. Inside this opening is a sleeve-type piston with a cross-sectional area of 1 square meter. The piston is pulled to the right at a constant speed. The pulling force is(Figure 2): F = ρshg = 1000 × 1 × 5 × 10 = 50,000 N. Figure 3: Modifying the structure to incorporate a fixed internal piston When I modify the piston...
Back
Top