HI my dear friends
i come back after few month absence:)
is there anyone here who know how to determine motor mode or generator mode in ansys maxwell?
i hope someone answer to this little question:)
have nice time
Hi all,
I am analysing a 2D D-shaped Neo Hookean model in contact with a Rigid link. The details are in the input file attached. Can someone guide me on how to solve this issue?:headbang:
Thanks,
Bruce
I have done the following Steps on a geometry consisting of
2 Beams
5 Frames
and an outer covering over that with Thugs on it for fix supports
Steps
1. Import Geometry to Workbench
2. Geometry cleaning(Suppressing the unwanted parts and sheet )
3. Open it in design Modeler
4. Meshing...
Hi all,
I am attempting to model an artery under internal pressure in ANSYS APDL.. This is my current attempt..
1. select solid 8 node 183 element type (and specify thickness)
2. select 5 parameter Mooney-Rivlin (for which I have constants)
3. create quarter area model dimensions
4. map mesh...
Hi experts!
Do you know how to export an ANSYS model into STL format?
I´ve only found some method for solid meshes here http://www.padtinc.com/blog/the-focus/color-3d-printing-ansys-ansys-mechanical-and-mechanical-apdl-results, but my model contains only BEAM4 elements.
Would it be possible...
Hello experts,
Is it possible to run several instances of Ansys Mechanical in Windows or Linux in parallel? How?
I need to dramatically speed up the solution of a large list of Ansys Mechanical jobs, typically more than 50000. Such analyses are performed by some script that runs each job in...
Dear experts,
I´m trying to model in ANSYS Mechanical (v14.5) the linear buckling behavior of a cylinder made of BEAM4 elements under combined loading (axial compression and bending moment) applied at the ends.
How should I set up the boundary conditions of a cylinder to keep rigid the ends...
ANSYS can be used to model creep in a number of different ways. If you are designing to ASME Section VIII, Div., 2 you might have to verify that your design meets the "shake down to elastic action" criteria. Basically, that means that the strains do not continue to increase over the number of...
All,
I recently completed a project where transient thermal boundary conditions are rotated around a cylinder for a general number of revolutions. In reality, the cylinder rotated but it was much easier to rotate the thermal conditions around the model in the ANSYS environment.
I used 360...
Hi everyone,
I'm here to ask you one thing of ansys, I made this model with solidworks and I imported into ansys as STEP files (which is the difference in how import solidworks file?), I defined the part that will be studied and applied as you can see in the attached photo, a linear...
Can anyone guide me how to mesh solid and shell 3d hemisphere with hex dominant approach in ansys mechanical APDL?
I found no such verification manual for 3d hemispherical meshing in ansys. What method should be applied and what element should be chosen appropriately to mesh this structure?
I...
I am new to both Ansoft Maxwell and HFSS and attempting to simulate transients on a 3d structure. I have a structure (hood of a car) designed in catia V5. I have imported the file into maxwell as .stp file. The Model analysis status verifies 'good' for all the parts. The 3d modeler window now...
Hello,
Suppose I want to glue a flat piece of sheet metal onto the outside of a rigid cylinder, and then find out the pressure that the glue is exerting onto the surface of the sheet metal. Assume that the deformation is elastic. Or suppose that in a variation of this problem, the sheet metal...
Hello everybody,
Three conductors are being simulated in Maxwell with a peak current. From Maxwell I extract the impedance matrix (3x3 matrix) of the three conductors. Conductors are placed on top of each other so there will be mutual inductances and resistances. The documentation on the...
hi every body
I want to analysis a beam with one degree freedom on apdl (ansys software)
This software give me a different period!
for beam with mass=stiffness=1 we must have 2π value for period but this program give me another answer.
Hi,
How do you define number of turns in a coil designed to operate at 100 kHz? Maxwell 2D axisymmetric treats the coils as a single conductor, how can we define number of turns. I would appreciate any response.
Thanks
Hi everyone! I am doing a simulation of threaded connection in ANSYS workbench and have some problem.
In this 2D model, the initial make-up is modeled by setting an "initial overlap" (shown in figure 1).
This is how I did:
- The initial contact between pin and box as "frictional" with...
Dear all,
is there anybody knows how to set a 2 degree-of-freedom movement in ANSYS Maxwell 2D transient model? I have two fixed current-excited coils and a free magnet. The magnet should be able to move in a 2D space under the Lorentz forces. However, there are only translation and rotation...
Hi,
I am new to Ansys workbench. I am doing analysis with simple fillet joint between two plate.
I would like to learn about creation of weld joint/connection between plates. Anybody can help me to create such realistic connection.
-Gajanan
Hi,
I want to make a script which will give message to a user as soon as we replace geometry in ansys workbench. Message will be about the material, A popup window will show default material is structural steel please assign appropriate material to all components.
Will it be possible with...
Hi, I am writing to you to ask for help.
I have a problem with the contact "Frictional". I'll show you screenshots of my settings and program the console errors. Everything will be shown in the screenshots. The problem is that between the beams and the top element and the bottom element is...
Hi,I wanted to know what is the difference between ANSYS Fluent/ANSYS and CATIA. And what purpose do both of these applications serve?
Furthermore, does Solidworks compete with CATIA? (If so, then i can focus on learning only one of them instead of two).I am just confused if i should learn ANSYS...
Hi, guys there is a quesetion:
Could ANSYS software be used for simulate system temperature and flow fields when fluid phrase change, such as in steam generators.
How to create a script geometry.
Is it possible?
some type?
I need to create a script to pipe conveyor.
After entering the input data is created geometry.
pls help me
Cfd -- familiar with ANSYS Fluent or CFX?
Is anyone here familiar with ANSYS Fluent or CFX? I have some questions about creating a simulation of subsonic flow over an airfoil. I have done the Cornell University tutorial. I then moved on to try simulating different arifoils, in particular S809...
Hello every body,
I am simulating a 1 dof spring-mass model in ansys workbench. I need to change the stiffness of spring at every substep based on an "if condition". It means that, in every substep, if a specified condition is satisfied, the stiffness will be changed to a defined value.
Also...
Hello everyone,
First of all, I want to excuse for my not perfect English since it isn't my mother tongue.
However, now to my problem, which I'm facing at the moment. As part of my master thesis I have to simulate the application of a fastening device, which I develope during my master...
I'm currently writing my thesis on a "Finite Element Analysis of rail fastening systems under dynamic load", and I'm using ANSYS Workbench 14.0 for that matter.
I don't know how to define the contact area for the clip and the angle guide plate, since it will be changing over time as the clip...
I have been easing my way into ANSYS and doing some modal analyses. The component I am modeling is a body of revolution with N=15 slots in it. The cross section looks much like the one in post #1 of this thread.
I started out by modeling the full 360° ring and requested the first 6 Modes...
Hi,
I am trying to model a simple plane stress problem using Ansys. I am using Ansys 14.0.
The problem is a simple square plate, without a corner, and with a hexagon hole around the midle. The boundary conditions consist of a constant pressure on the top side, and full constrain on the...
I have an assembly of two 2D surfaces. I modeled it on SolidWorks however, I could not import it to Ansys in any format. I tried SLDASM, Step and IGES. I tried modelling the same on Workbench modeller. However, I could not figure out a way to model 2D assemblies on the modeller.
Can someone...
Hi all,
I have started learning ansys workbench for steady state heat transfer based analysis.
I am doing this analysis to validate analytical results given for heat transfer from a single plate fin.
The fin tip is given a base temperature and heat transfer is calculated for natural...
Hello all!
I am curious. Sometimes I would like to do a trade study on a mechanical component; so in the interest of time, I think I would use 2D analysis techniques so that a) I can save time on the front end in the CAD package and b) save time on the analysis side of things. But I want...
I was told in a meeting, in passing, not to pay any attention to the deflection results that come out of a free vibration problem. Can someone clarify why or point me to a good resource where I can inform myself?
Thanks,
KC
Hi All,
If anyone could help me with a problem I'm having, it would be great.
I've been using Ansys Maxwell for about 6 months now, and I've gotten the hang of it. I mainly simulate 2 phase inductors. Until yesterday, I've had no problem, but for some reason, I'm not getting any...
Static structural simulation with rigidity and strength criterias
I have a 10 mm imbus key which is constrained on the shorter end, while there's a force on the longer end simulating ccw rotation (i.e. "unscrewing"). I have no problem setting the force and simulating deformation and...
Hi all!
I am trying to solve a transient contact analysis in Ansys 14.0
The problem is a Bouncing Rectangle problem. That's the procedure I use:
/Prep7
k,1,-30,0,0
k,2,30,0,0
k,3,-30,30,0
k,4,0,30,0
Create->Areas->Arbitrary->Through Keypoints !Create the ground
k,50,-20,30,0...
I have a project where I need to simulate the magnetic forces with ANSYS. I'm and intermediate ANSYS user but I have really only worked with APDL, and if possible I would like to do it in the GUI.
So my problem is that I have only ever done structural and thermal models in ANSYS.
I am...
ansys -- heat transfer within pipes and with surroundings
hello ,
am doing my master in architecture n currently in my thesis stage and the thesis is about heat transfer within pipes and their influence on the surrounding atmosphere.
i wish to know which is the right kind of analysis in...
I am trying to run a simulation (transient analysis) in ANSYS Workbench of a rolling tire on a flexible pavement surface. The tire is a truck tire with pressure of 0.7 MPa.
I defined various outputs at consequential small time steps, and I can see the tire gradually inflating until (what...
Hello,
Greetings! How do I get the convective surface matrix from ANSYS for 3D thermal problem. Consider a volume, where some of its surfaces are subjected to convective boundary conditions. What is the way to get those (only convective surface) matrices generated by ANSYS. Any help in...
Dear Friends,
Hi,I am senior mechanical engineering student and I'm working on my
final project which is designing an AGV vehicle.I designed a space
chassis for it and have a problem with analyzing the joint I designed
using Solidworks.I do not know how can I should define support...
I have a very large ANSYS model with many loads and load cases that results in an array of stresses and strains. I need to update and refine the geometry and loading in a small portion of it, while maintaining accuracy in the results for that portion. This includes the inclusion of the boundary...
Hello everyone, I´m programming in ANSYS APDL and I want to make a parametric analysis.
Because I need to join a lot of points with the bspline function I can´t make this
FLST,3,10,3
FITEM,3,1
FITEM,3,-10
BSPLIN, ,P51X
I need to write in my program all the points...
Hello,
I have the following problem: I would like, from a tungsten filament which an electric current is imposed, find the temperature emitted from the filament (Joule heating) on ansys workbench.
I have to study a thermoelectrical , but I can not find any tutorial.
Does anyone have...
http://img715.imageshack.us/img715/2498/11489662.jpg
The pressure will push component "a" to move downwards and push component "b" to move upwards.
Component "a" and "b" will only be moved in vertical direction (90degree).
There will be friction force occurs on the sliding surface...
Hello all,
Here is a new APDL book.
https://www.amazon.com/gp/product/146641135X/ref=oh_details_o00_s00_i00?ie=UTF8&psc=1
I bought a copy to check it out.
Thanks
Matt
I want to do an analysis in ANSYS LS-DYNA. After applying element types, materials and loads to my model, I solved the problem. but after finishing the solution all of the deformations, plastic strains and ... are 0. (the applied force is very high and I expect to see rupture in a large area of...
Hi, I am recently new to Ansys using version 11 APDL.
Does anyone know of any beginners links to basic training or any decent books?
I am finding playing around and using just the help menu very difficult.
I'm mainly interested in some basic tutorials writing code to create a part and...