Receiver Definition and 110 Threads

Homework Statement The tuning circuit in an FM radio receiver is a series RLC circuit with a 0.200 µH inductor a. The receiver is tuned to a station at 104.3 MHz. What is the value of the capacitor int he tuning circuit? b. FM radio stations are assigned frequencies every 0.2 MHz, but two...

A photon or electromagnetic wave has the speed of light in vacuum and the distance, from the photons point of view, then becomes zero. The photon is then an energy exchange between particle A and particle B, and it is from the photons view at startpoint A and endpoint B at the same time. And it...

As far as I understand it... Each satellite transmits a signal that the receiver receives. This signal consists of (at least) a satellite identification together with a time-stamp of when the signal was sent and its position at that time. The receiver calculates the distance from the...

Homework Statement super heterodyne receiver made up of a LNA a mixer and an IF respectively. LNA NF1=? G1=? MIXER NF2=2.5DB G2=-3.5DB IF AMPLIFIER NF3=28DB G3=7DB THE OVERALL NF OF THE RECEIVER SHUD NOT EXCEED 6.5DB AND THE OVERALL GAIN SHOULD NOT EXCEED 32DB Homework...

I have included a picture of what I would like to be able to make. I know that older phones operate on very specific MHz signals and that the newer ones are 2.4, or 5.8 GHz. I know there are scanners out there. But the purchase of one could be illegal, right? So why not make my own, to pick...

I have constructed a small one-transistor regenerative receiver, and I have been getting weird results with reception. I have noticed that simply touching parts of the radio, such as the antenna or around where the antenna is attached, will provide great reception. However, when I am not...

My task is to estimate / compute accuracy of a gps receiver. My experiment would involve using three GPS receivers and post processing software. following is the nomenclature i would follow for explaining my question. Normal GPS receiver: This is the receiver in test, a simple 12 channel...

Hello, I am a final year student of BEE Telecom. I chose my Final Year Project to design a Transmitter and Receiver for GPR. GPR has already been developed in my institute. It uses VNA as its source. Since VNA is a multipurpose device and the already-implemented project used it to find S11...

I've developed a new concept called "Ambient Light Ignoring Infrared Active Distance Sensor". It consists of a transmitter with an infrared LED which uses a traditional LM555 timer to oscillate a frequency of 5kHz and a modified receiver which consists of a common emitter setup, NPN...

Homework Statement An electric dipole antenna used to transmit radio waves is oriented vertically. At a point due north of the transmitter, how should a second electric dipole antenna be oriented to serve as a reciever? Homework Equations Im not sure if my answer below makes sense, is...

Please help me in removing my mistake, since i see 3 satellite required to locate an place on Earth and synchronization of receiver clock with gps satellite. [ I have assumed at any moment a place on Earth will see certain satellite at a certain distance from it in the sky. That is a...

I am designing a game where you would shoot an IR gun at an object that would turn a light on and stay on until manually reset. I don't know much about electronics and any help would be appreciated.

Homework Statement Determine the SNR for the spacecraft that uses a transmitter power of 16 W at a frequency of 2.4 GHz. The transmitter and receiver antenna gain are 28 dBi and 60 dBi, respectively. The distance from the space- craft to ground is 2 ϫ 1010 m, the effective noise temperature...

Voltage Drop Between Sender & Receiver ...( help needed ASAP , Thanks in advance ) hello every body I'm EE student and I'm new member here ... in a deep need for your help & knowledge I'm doing some reading about the power transmitted from the sender to the receiver end , As we all know...

Hi everyone I am an amateur modeler and am very interested in physics and am trying to to make a model car/roadway that can move and be controlled by a computer. I have managed to placing a motor in the models, but have not found battery's which are small enough and can run it. So what i...

with synchronization what the gps receiver does is compute time difference between his current time (synchronized with atomic clock onborad each satellite) and the time tag of a satellite when the signal was sent. This difference gives the travel time of an signal from the satellite and hence...

Dear all, I am trying to understand what is the difference between a transmitter and receiver antenna. If I recall correctly an antenna is a dipole so you can always use it to either transmit or either receive. All the antennas that are used for transmitting purposes come with some...

Hello, is anyone can guide me to built a costas receiver. At the input of a mixer the LO and RF signal creates an IF signal. This IF is the frequency difference of LO and RF irrespective of their position of frequency spectrum, i mean IF=LO-RF or IF=RF-LO. I need to track this IF signal at the...

I was going thu AM26LS32 diff line receiver. The data sheet has a ckt diagram for the input stage. But I don't understand it. I have attached the input stage from datasheet(page3) The input stage actually looks like a push pull output stage. What is the function of the 100K resistors and...

Hey all! I have just constructed a RF circuit to try out. I made use of the T5-434-5V and the R5-434-5-128 transmitter and receiver pair and also the HT12E and HT12D as the encoder and decoder for the transmitter and receiver respectively. The schemetic I used can be found on page 6 of this...

Homework Statement A radio receiver is set up on a mast in the middle of a calm lake to track the radio signal from a satellite orbiting the Earth. As the satellite rises above the horizon, the intensity of the signal varies periodically. The intensity is at a maximum when the satellite is 1...

hello i am new, i thinking to make a fm radio receiver but i don't know what i need (capacitor, oscillator etc) can someone help me with more knowledge than me ? if you have link or something else that maybe help me is welcome. i search the internet but i don't can find anything that suit in my...

Homework Statement I am totally new to MATLAB. My lecturer wasn't aware of that and just gave us an assignment about explaining the phenomena Hartley Receiver using Simulink.Homework Equations The diagram is attached as first picture. Using Simulink, prove that the image signal is alleviated at...

Hey guys, do any of you know of a transmitter/receiver device that can let you know the distance between them? I really need some help fast and would really appreciate it!

Hi Please don't give me another warning for posting in a wrong forum. Seriously, in my view this belong here in "General Discussion" forum. Where I'm placed these days here we have electricity blackouts several times a day, sometimes for as long as 3 hours at one time. My laptop could run...

As title, my lecturer had given me a project which to design a Analog RF Walkie talkie which in Frequency Modulation and carrier can be between 50Mhz - 200Mhz. I had actually designed the transmitter part but quite confuse in receiver part. Can any master can actually give me some general idea...

Homework Statement A radio reciever requires a tuning circuit that will select 88MHz but reject 99MHz, design a series LCR circuit that will filter this way for a 8 ohm load resistance. State any assumptions. The circuit should be in the following format...

I am using the following receiver and transmitter for my project to form a ultrasonic communication system. I transmitted 5V Peak to peak voltage, 40 Khz frequency sinusoid from the transmitter and received the signal through the receiver. But the receiver shows the peak-to-peak voltage of about...

On page 109 of David Adamy's book EW 101: A First Course in Electronic Warfare there is the following comment: I'm not sure exactly why the tuning rate "must" not exceed this value...can anyone clear this up for me? Maybe this is something really simple and I am just missing it...

http://www.fastcompany.com/blog/ariel-schwartz/sustainability/forget-solar-power-nokia-developing-radio-wave-powered-cell-phone Now, I am sure at least some of you have heard of this technology that Nokia is developing. It creates around 5 mW right now. My question is, how do you make an...

this is our last quiz on communication.. fortunately, the whole class got zero on this quiz so the professor arranged a retake and made it a take home exam instead.. this is my last hope on passing the course.. so any help would be greatly appreciated.. 1.A superheterodyne receiver having an...

Hi Just have a quick question, for audio input (AUX) into speakers would it be possible to make a powerless radio receiver plug in, or would it require power? Thanks

I have a question about pressure equalization. I have 2 receiver thermically insulated (adiabatic) and connected via a valve, one receiver 10 cu/ft at 100 psig and 350 F, the other receiver is 1 cu/ft at 0 psig and 60 F. using n=1.406, what would be the equalizing pressure and temperature when I...

Hay to all this is my first post here :) First of all thanks on all who try to help me :) Second of all i got this "task" to make a model of this picture: http://img200.imageshack.us/i/slikanapravitimodel.jpg/ http://img200.imageshack.us/img200/493/slikanapravitimodel.th.jpg...

If you have ever seen the benchmark of an audio video receiver, you will see how the power drops off as more channels are driven at the same time. For example, a benchmark done on my receiver, the Yamaha RX-V3900 showed 189 watts into one channel, and only 88 watts into seven channels. Is...

Why does my body act as a radio Receiver.Last year i accidently grabed the socket to my computer speakers while they were turned on at the power outlet.The computer speakers were not connected to the computer and we do not have a radio receiver at all in our home.I only held the plug for one...

Hi everyone. I'll describe my setup first, then state my question. I have a receiver chain consisting of the following (where all conversion factors are assumed to be scalar and constant under the conditions in which I use them): 1) An APD (avalanche photodiode): Input: Optical power P1in...

Hey PF, I want to resurrect an old robot radio I have sitting around. What exactly is involved with building an AM/FM receiver?

I'm not sure whether to use this: Class 1 http://www.kanda.com/products/Sena/PARANI-ESD1000.html or Class 2 http://www.kanda.com/products/Sena/PARANI-ESD200.html I'm planning to use it in an elevator for a senior project and I would like some suggestions or advice on which to...

I want to design a fm receiver circuit for the frequency range of 144-146Mhz.Kindly suggest me a suitable ic for the same.

well i m designing a simple circuit in which a bulb is turned on and off by a simple household remote control. Normal remote control gives IR of 38 khz so i m using TSOP 1738, there is also an alternative of HRM 3800. Well i m having a problem that neither of them r working. When i press the...

I've been looking all over the Internet for what I thought would be an easy thing to find instructions on. Unfortunatley, anything that comes close either complicates the matter with extra features or assumes I know a lot more about electronics than I do... I need to build a very simple...

Hi all, I have a plan of building myself a VHF receiver that can pick up the air band (108-136 Mhz). I want to connect it than with an antenna that I plan to set it up on my rooftop. Can anybody give me some working schemes and tips how to build such thing? Thanks in advance.

How can I use radio wave to turn on/off a siren? I think it is possible for me to design a radio signal through this schematic: http://www.aaroncake.net/circuits/fmtrans.htm The problem is, how do I design a receiver that can switch on a siren by receiving the radio signal?

The objective is to "design and construct an FM radio receiver" that is able to tune to commercial FM radio broadcast channels spanning from "87.5 MHz to 108 MHz", and to produce audible demodulated output. can anybody help me with a simple circuit for this assignment with proper values for...

Homework Statement Designing an FM Radio Receiver. You enjoy listening to KONG-FM, which broadcasts at 96.6 MHz. You detest listening to KRUD-FM which broadcasts at 96.5 MHz. You live the same distance from both stations and both transmitters are equally powerful, so both radio signals produce...

Im working on a project and i would like know where i can find an ebook or site that could help me understand this technology. I will use an IR photodiode (Rx) and an IR emitter (Tx). the signal being sent will originate from a RS-232. So basically i have RS-232 <-> IR <-> RS-232, and so i...

Homework Statement A QB sees his receiver 25 m downfield and throws the ball to him at 45 degress, with speed 22 m/s Homework Equations well, speed=distance/total time, so i used the equation:d(y)=v(oy)t + .5a(y)t^2 parentheses indicate subscripts... The Attempt at a Solution...

can anyone describe wat is dB level. can dB level be showed through receiver or field strength meter? thx for helping

[b]1. Homework Statement [ i was asked to measure the signal strength. so in my set up for the experiment, is the field strength meter needed together with the receiver. how am i going to set these together at the antenna.izzit , connect the receiver to the battery, antenna to the receiver, AND...