Calculating Minimum Trailing Distance in a Reaction Time Scenario

  • Thread starter Thread starter Argento7
  • Start date Start date
  • Tags Tags
    Minimum
AI Thread Summary
To avoid a collision while driving at 108.1 km/hr (30.02 m/s), a driver must account for a 1-second reaction time delay before applying brakes. The key point is that during this 1-second delay, the vehicle will travel approximately 30.02 meters. Therefore, to maintain safety, the driver should maintain a minimum distance of at least 30.02 meters behind the car in front. This ensures that both vehicles can decelerate without colliding. Understanding this distance is crucial for safe driving practices.
Argento7
Messages
3
Reaction score
0
Hello,

Homework Statement



You are driving along the New York State Thruway in a line of cars all traveling at a constant speed of 108.1 km/hr (Which I converted to 30.02 m/s). The car in front of you applies its brakes for maximum acceleration. You then apply your brakes to achieve the same maximum acceleration after only a 1 s delay due to reaction time. What distance behind the car in front of you must you be to avoid a collision?


Homework Equations



How can I factor in the 1s delay on the time?

All the equations for the problem are located here:
http://www.glenbrook.k12.il.us/gbssci/phys/Class/1DKin/U1L6a1.gif


The Attempt at a Solution


I set the origin and my initial position to 0 for the car in front of you. I also had tried several times to figure out the acceleration.
 
Last edited by a moderator:
Physics news on Phys.org
Argento7 said:
Hello,

Homework Statement



You are driving along the New York State Thruway in a line of cars all traveling at a constant speed of 108.1 km/hr (Which I converted to 30.02 m/s). The car in front of you applies its brakes for maximum acceleration. You then apply your brakes to achieve the same maximum acceleration after only a 1 s delay due to reaction time. What distance behind the car in front of you must you be to avoid a collision?

Homework Equations



How can I factor in the 1s delay on the time?

All the equations for the problem are located here:
http://www.glenbrook.k12.il.us/gbssci/phys/Class/1DKin/U1L6a1.gif

The Attempt at a Solution


I set the origin and my initial position to 0 for the car in front of you. I also had tried several times to figure out the acceleration.

Welcome to PF.

Hint: You don't need to know actual acceleration. Just that it is the same and yours is 1 s later.

If you plotted a graph of velocity for each car they will look the same ... except for the 1 sec delay. So long as you start deceleration before you reach the point on the road that the car ahead starts then you should maintain the same distance to stopping.

For a 1 second margin then how does that translate into distance?
 
Last edited by a moderator:
Hi, you were traveling at 30.02m/s, so in 1 second you will cover 30.02m, and you need 1 second to react. So at least you have to be a 30.02 meters distance from the car that is ahead of you.
 
Kasper_NYC said:
Hi, you were traveling at 30.02m/s, so in 1 second you will cover 30.02m, and you need 1 second to react. So at least you have to be a 30.02 meters distance from the car that is ahead of you.

There you go. You're ready to drive safely.
 
Thank you both so much :approve:
 
Thread 'Voltmeter readings for this circuit with switches'
TL;DR Summary: I would like to know the voltmeter readings on the two resistors separately in the picture in the following cases , When one of the keys is closed When both of them are opened (Knowing that the battery has negligible internal resistance) My thoughts for the first case , one of them must be 12 volt while the other is 0 The second case we'll I think both voltmeter readings should be 12 volt since they are both parallel to the battery and they involve the key within what the...
Thread 'Struggling to make relation between elastic force and height'
Hello guys this is what I tried so far. I used the UTS to calculate the force it needs when the rope tears. My idea was to make a relationship/ function that would give me the force depending on height. Yeah i couldnt find a way to solve it. I also thought about how I could use hooks law (how it was given to me in my script) with the thought of instead of having two part of a rope id have one singular rope from the middle to the top where I could find the difference in height. But the...
Back
Top