Electron shot between two charged plates, does it hit?

AI Thread Summary
An electron is shot between two charged plates with an upward electric field of 2.00x10^3 N/C, making an angle of 45 degrees and traveling at 6.00x10^6 m/s. The calculations reveal that the electron's horizontal displacement is 10.176 cm, exceeding the length of the plates, but it must also be checked for vertical displacement. The vertical motion analysis shows that the electron reaches a height of 0.0272 m before hitting the upper plate. Therefore, the electron will strike the upper plate early in its trajectory due to its high speed and angle of launch. The conclusion confirms that the electron does indeed hit the upper plate.
mhen333
Messages
16
Reaction score
0

Homework Statement



A uniform, upward electric field E of magnitude 2.00x10^3 N/C has been set up between two horizontal plates by charging the lower plate positively and the upper plate negatively. The plates have length L = 10.0 cm and separation d = 2.00 cm. An electron is then shot between the plates from the left edge of the lower plate. The initial velocity Vi of the electron makes an angle theta = 45.0 degrees with the lower plate and has a magnitude of 6.00x10^6 m/s. (A) Will the electron strike one of the plates? (B) If so, which plate and how far horizontally from the left edge will the electron strike?

Homework Equations



<br /> F = ma_{y}<br />

<br /> a_{y} = \frac{F}{m} = \frac{eE}{m}<br />

The Attempt at a Solution




Okay, I think I have this. The components (X and Y) of the velocity are

<br /> V_{x_{0}} = (6.00 * 10^6 \frac{m}{s})(\cos {\frac{\pi}{4}}) = 4.24 * 10^6 \frac{m}{s} \hat{i}<br />

and

<br /> V_{y_{0}} = (6.00 * 10^6 \frac{m}{s})(\sin {\frac{\pi}{4}}) = 4.24 * 10^6 \frac{m}{s} \hat{j}<br />


I will start with finding the acceleration,

<br /> a_{y} = \frac{F}{m} = \frac{eE}{m}<br />

<br /> a_{y} = \frac{(-1.6*10^-19 C)*(2 * 10^3 N/C}{9.109 * 10^-31 kg}<br /> a_{y} = -3.5 * 10^14 \frac{m}{s^2}<br />


Using substitution and solving for t:
<br /> t = \frac{-2 * V_{x}}{a} = \frac{-2(4.24 * 10^6 m/s}{-3.5 * 10^14 m/s^2} = 2.4 * 10^{-8} s<br />

So in that length of time, the electron will travel distance:

<br /> \Delta X = V_{x_{o}} * t = (4.24 * 10^{6} m/s) * (2.4 * 10^{-8} s) = .10176 m<br />

Since 10.176 cm is greater than the 10cm length of the plates, am I done at this point?
 
Physics news on Phys.org
You are not done. You have not shown that the electron will not hit the top plate before it clears the end of the bottom plate. Calculate how high vertically the electron will rise and compare that with the plate separation.
 
Oh, thanks!

So then,

<br /> \Delta y = v_{0} * t - \frac{a * (t/2)^{2}}{2}<br />

<br /> <br /> \Delta y = 4.24*10^6 \frac{m}{s} * t - \frac{3.5 * 10^{14} \frac{m}{s^{2}} * t}{2}<br /> <br />

Setting vertical displacement equal to 0.02m, and solving for t, I get

<br /> t = 6.416 * 10^{-9} s<br />

for the time when the electron hits.

At that point, finding the X displacement gives me

<br /> \Delta x = .0272m<br />

So it DOES hit, and very early on. Which makes sense, since it's going ridiculously fast to begin with, and angled at 45 degrees.
Thanks for your help, much appreciated.
 
Thread 'Voltmeter readings for this circuit with switches'
TL;DR Summary: I would like to know the voltmeter readings on the two resistors separately in the picture in the following cases , When one of the keys is closed When both of them are opened (Knowing that the battery has negligible internal resistance) My thoughts for the first case , one of them must be 12 volt while the other is 0 The second case we'll I think both voltmeter readings should be 12 volt since they are both parallel to the battery and they involve the key within what the...
Thread 'Struggling to make relation between elastic force and height'
Hello guys this is what I tried so far. I used the UTS to calculate the force it needs when the rope tears. My idea was to make a relationship/ function that would give me the force depending on height. Yeah i couldnt find a way to solve it. I also thought about how I could use hooks law (how it was given to me in my script) with the thought of instead of having two part of a rope id have one singular rope from the middle to the top where I could find the difference in height. But the...
Back
Top