How can we improve motor control for our robotic television camera positioners?

AI Thread Summary
The discussion focuses on improving motor control for robotic television camera positioners, specifically using flat pack brushless DC motors with a 5-wire onboard control system. The team is facing challenges with achieving a "dead" spot at the center of a two-axis joystick, which is necessary to ensure zero speed when the joystick is not engaged. They require a transition from a "creep" speed to approximately 30-40 degrees per second. Suggestions include implementing built-in hysteresis around the 5V center voltage to create the desired dead zone. The team plans to consult with the motor manufacturer, Maxon, for potential solutions.
horngroup
Messages
2
Reaction score
0
We are many years out of school. We are building robotic positioners for television cameras. Our experience in the mechanical design is extensive. We are seeking direction in motor control. The motors which we would like to try are flat pack brushless dc motors with 5 wire on board control. The manufacturer can supply with an input which causes rotation in one direction from 0-5v and reverses from 5-10v. We use a two axis joystick as we rotate horizontally and vertically. We have trouble with our control at center rest of the joystick, as we need a "dead" spot in the center to insure 0 speed. We need to go from a "creep" speed to about 30-40 deg/sec. We would think that with allthe robotics out there this is reinventing the wheel. Any help out there?
Horngroup
 
Engineering news on Phys.org
horngroup said:
We are many years out of school. We are building robotic positioners for television cameras. Our experience in the mechanical design is extensive. We are seeking direction in motor control. The motors which we would like to try are flat pack brushless dc motors with 5 wire on board control. The manufacturer can supply with an input which causes rotation in one direction from 0-5v and reverses from 5-10v. We use a two axis joystick as we rotate horizontally and vertically. We have trouble with our control at center rest of the joystick, as we need a "dead" spot in the center to insure 0 speed. We need to go from a "creep" speed to about 30-40 deg/sec. We would think that with allthe robotics out there this is reinventing the wheel. Any help out there?
Horngroup

So zero rotation velocity is achieved around 5V? The manufacturer should have some built-in hysteresis around this center voltage, so that you get the dead spot that you want. Something like 100mV hysteresis or so. Or basically a 100mV dead zone around 5V that gives zero rotational velocity. Can they give that to you?
 
Thanks for the reply. We'll check with the motor people (Maxon)
 
I used to be an HVAC technician. One time I had a service call in which there was no power to the thermostat. The thermostat did not have power because the fuse in the air handler was blown. The fuse in the air handler was blown because there was a low voltage short. The rubber coating on one of the thermostat wires was chewed off by a rodent. The exposed metal in the thermostat wire was touching the metal cabinet of the air handler. This was a low voltage short. This low voltage...
Hey guys. I have a question related to electricity and alternating current. Say an alien fictional society developed electricity, and settled on a standard like 73V AC current at 46 Hz. How would appliances be designed, and what impact would the lower frequency and voltage have on transformers, wiring, TVs, computers, LEDs, motors, and heating, assuming the laws of physics and technology are the same as on Earth?
Thread 'How Does Jaguar's 1980s V12 Dual Coil Ignition System Enhance Spark Strength?'
I have come across a dual coil ignition system as used by Jaguar on their V12 in the 1980's. It uses two ignition coils with their primary windings wired in parallel. The primary coil has its secondary winding wired to the distributor and then to the spark plugs as is standard practice. However, the auxiliary coil has it secondary winding output sealed off. The purpose of the system was to provide a stronger spark to the plugs, always a difficult task with the very short dwell time of a...
Back
Top