What are the Sources of Dispersion in Fibre Optics?

AI Thread Summary
Sources of dispersion in fiber optics include modal dispersion, which occurs in multimode fibers due to different group velocities of modes, and is absent in single-mode fibers. Material dispersion arises from varying group velocities of different wavelengths, influenced by the spectral width of the light source. Waveguide dispersion is related to the fiber's core and cladding design, affecting how light is distributed and can be adjusted to achieve zero dispersion at specific wavelengths. In dispersion-shifted fibers, the combination of negative waveguide dispersion and positive material dispersion allows for zero dispersion at wavelengths like 1550nm. Understanding these concepts is essential for optimizing fiber optic performance and minimizing signal distortion.
-DJL-
Messages
2
Reaction score
0
I'm confused as to sources of dispersion in a fibre. Any clarification would be appreciated.

Modal (Intermodal) dispersion: pulse spreading due to different group velocities of different modes in the fibre. Each mode has a slightly different n-effective hence the different Vg for each mode. Not present in single mode fibres, as there's only one mode. Can also be though of as different ray paths - light traveling down the centre of the fibre will reach the end before light which is TIR'ing its way along.

Intramodal covers the following;

Material Dispersion: Spectral width; each spectral component will in general travel with a different group velocity -> difference wavelengths travel at different speeds. Sources of spectral width: LED greater width than a laser, and sidebands caused by modulation.

Waveguide dispersion: ?? changes in the distribution of light between core and cladding? Dependant on core diameter?


So with Dispersion Shifted Fibres :- single mode fibre, therefore no modal dispersion. Waveguide dispersion is negative and material dispersion is positive -> therefore at a particular wavelength they cancel -> 0 dispersion. Wave guide dispersion can be shifted so that the 0 occurs at a different wavelength (1550nm)
 
Last edited:
Engineering news on Phys.org
...wave-guide dispersion depends on the shape, design, and chemical composition of the fiber core. Only 80 percent of the power from a light source is confined to the core in a standard single-mode fiber, while the other 20 percent actually propagates through the inner layer of the cladding. This 20 percent travels at a faster velocity because the refractive index of the cladding is lower than that of the core (Keiser, 1983). Consequently, signals of differing frequencies and wavelengths are dispersed and the pulse becomes indistinguishable (Lerner, 1997).

"www.cmste.uncc.edu/new/papers/Attenuation%20in%20Fiber%20Optics.doc"[/URL]
 
Last edited by a moderator:
That's cool stuff. What part is confusing? What learning resources do you have available, and what have you read so far on the web?
 
Doh! dlgoff is quick today!
 
dlgoff - Thanks, that link, along with going through the maths, has helped clarify waveguide dispersion.

A great book on the subject is Ghatak, Ajoy and K., Thyagarajan. (2000). Introduction to Fibre Optics. Cambridge, UK : Cambridge University Press.
 
I used to be an HVAC technician. One time I had a service call in which there was no power to the thermostat. The thermostat did not have power because the fuse in the air handler was blown. The fuse in the air handler was blown because there was a low voltage short. The rubber coating on one of the thermostat wires was chewed off by a rodent. The exposed metal in the thermostat wire was touching the metal cabinet of the air handler. This was a low voltage short. This low voltage...
Hey guys. I have a question related to electricity and alternating current. Say an alien fictional society developed electricity, and settled on a standard like 73V AC current at 46 Hz. How would appliances be designed, and what impact would the lower frequency and voltage have on transformers, wiring, TVs, computers, LEDs, motors, and heating, assuming the laws of physics and technology are the same as on Earth?
Thread 'How Does Jaguar's 1980s V12 Dual Coil Ignition System Enhance Spark Strength?'
I have come across a dual coil ignition system as used by Jaguar on their V12 in the 1980's. It uses two ignition coils with their primary windings wired in parallel. The primary coil has its secondary winding wired to the distributor and then to the spark plugs as is standard practice. However, the auxiliary coil has it secondary winding output sealed off. The purpose of the system was to provide a stronger spark to the plugs, always a difficult task with the very short dwell time of a...

Similar threads

Back
Top