What is the significance of using U/2I in four point probe theory?

AI Thread Summary
The discussion centers on measuring sheet resistance (R_square) using a four-point probe setup, where the user is experiencing discrepancies in resistance values compared to a reference system. The user has applied geometric and correction factors but is puzzled by a factor of two difference in their results. Other participants suggest reviewing the application of the geometric correction and emphasize the importance of showing work for accurate troubleshooting. There is also a question about the measurement method being used, specifically if it relates to the van der Pauw technique. The conversation highlights the need for clarity in methodology to resolve measurement inconsistencies.
ScieneShines
Messages
2
Reaction score
0
Dear Ladys and Gentlemans,

I want to measure the sheet resistance R_square on a printed product.
My measuring equipment consists a SMU to supply and measure and a four point Probe by Jandel.
As output size I get the electrical resistance R (basically the measured Voltage U divided by the supply current I)
So I have to multiply the geometric factor and a correction factor (correction factor because the width is small)

The derivation for the geometric factor I have found on :
http://www.four-point-probes.com/four-point-probe-...

And the correction factor table is shown here, in my case its on page 54
https://www.iiserkol.ac.in/~ph324/StudyMaterials/G...

Funny but true, I get twice the value than in the reference measurement system (eddy current technology)
So may we can discuss why?
And the bigger Question: why is the resistance calculated in the derivation with U/2I.
In my opinion there is no superposition of currents because they have a different sign.
Thank you in advance,
ScieneShines
 
Engineering news on Phys.org
Well, since you didn't show any of your work, we would have no idea where any error lies.

Now my disclaimer. Not my area of expertise, so take anything I mention merely as a 'second pair of eyes.'

From doing a spot read/scan of the links you supplied, you may have mis-applied the geometry correction. See especially pgs 4 thru 7 of the PDF you referenced. That seems to answer your 'why the factor of two' question and also cover the 'factor of two' error you seem to be getting.

Hopefully the above is at least a place to start!

Cheers,
Tom
p.s. Since this is a schoolwork question, I have requested it be moved to the Homework forum.
 
  • Like
Likes Jody
First things first : Thank you for your answer and no this is definitivly not a Schoolwork, Homework or anything else... Did you do those things in school? Respect for that.

I'm 100% sure that i used the correct correction factor.
Symmetry condition are given.
 
Welcome to the PF. :smile:
ScieneShines said:
I'm 100% sure that i used the correct correction factor.
I agree with @Tom.G that we need to see your work to be able to help you.
 

Thread 'Why does the amperage go real high if there is a low voltage short?'

I used to be an HVAC technician. One time I had a service call in which there was no power to the thermostat. The thermostat did not have power because the fuse in the air handler was blown. The fuse in the air handler was blown because there was a low voltage short. The rubber coating on one of the thermostat wires was chewed off by a rodent. The exposed metal in the thermostat wire was touching the metal cabinet of the air handler. This was a low voltage short. This low voltage...
View full post »

Thread 'How might electronics be different if AC voltage was 72V at 45 Hz?'

Hey guys. I have a question related to electricity and alternating current. Say an alien fictional society developed electricity, and settled on a standard like 73V AC current at 46 Hz. How would appliances be designed, and what impact would the lower frequency and voltage have on transformers, wiring, TVs, computers, LEDs, motors, and heating, assuming the laws of physics and technology are the same as on Earth?
View full post »
Thread 'How Does Jaguar's 1980s V12 Dual Coil Ignition System Enhance Spark Strength?'

Thread 'How Does Jaguar's 1980s V12 Dual Coil Ignition System Enhance Spark Strength?'

I have come across a dual coil ignition system as used by Jaguar on their V12 in the 1980's. It uses two ignition coils with their primary windings wired in parallel. The primary coil has its secondary winding wired to the distributor and then to the spark plugs as is standard practice. However, the auxiliary coil has it secondary winding output sealed off. The purpose of the system was to provide a stronger spark to the plugs, always a difficult task with the very short dwell time of a...
View full post »

Similar threads

How to Convert Four Point Probe Resistance to Conductivity?
Replies
1
Views
2K
Questions on Rs measurement by four point probe device
Replies
1
Views
2K
A 4 probe conductivity in discs (Smits)
Replies
3
Views
2K
Four Point Probe Measurement Help for 500 nm Ni Coating
Replies
4
Views
4K
Four Terminal Sensing Measurement for Printed Conducting Inks
Replies
1
Views
3K
I What Key Issues Should Cosmologists Address in the ΛCDM Model?
Replies
1
Views
3K
I Muon g-2 as a constraint on new physics
Replies
18
Views
4K
What is the significance of the Rubik Group in combinatorial species theory?
Replies
8
Views
3K
Which Papers Will Shape Future Quantum Gravity Research?
Replies
2
Views
3K
Advice for Honours Astrophysics/Applied Mathematics
Replies
10
Views
5K

Hot Threads

Recent Insights

Back
Top