Speed distance and not a lot of hair left

  • Thread starter Thread starter steveandy2002
  • Start date Start date
  • Tags Tags
    Hair Speed
AI Thread Summary
The discussion focuses on calculating the time it takes for a ball to fall 100 meters with an initial velocity of 72 km/h under gravity of 10 m/s². The user attempts to use the equation s = ut + 0.5gt², and after some calculations, arrives at a time of approximately 2.9 seconds. Another participant suggests that the user should convert the initial velocity from km/h to m/s and directly substitute the values into the equation to solve for time. The conversation emphasizes the importance of unit conversion and solving the quadratic equation derived from the formula. The final takeaway is that the user can indeed solve for time using the s = ut + 0.5gt² formula with the correct unit adjustments.
steveandy2002
Messages
6
Reaction score
0

Homework Statement


a balls inital velocity is 72 km/ph and falls 100 meters with gravity @ 10 meters per second and i need to work out the time it takes to fall to ground. i was given s=ut+0.5*gt^2

Homework Equations


s=ut+0.5gt^2
v^2=u^2+2as
t=(v-u)/a

The Attempt at a Solution



v2=u2+2as
v=squr u^2+2as
v=squr 20^2+2*10*100
v=48.98979486

t=(v-u)/a
t=(48.98979486-20)/10
t=2.898979486 seconds

100=20*2.898979486+0.5*10*2.898979486^2

is this correct??
and is there a way to do this with just the s=ut+0.5at^2 formula ?
 
Last edited:
Physics news on Phys.org
hi steveandy2002! :smile:

(try using the X2 button just above the Reply box :wink:)
steveandy2002 said:
a balls inital velocity is 72 kph and falls 100 meters with gravity @ 10 meters per second and i need to work out the time it takes to fall to ground.

and is there a way to do this with just the s=ut+0.5at^2 formula ?

s = 100, u = 72, a = 10 …

what's the difficulty? :confused:
 
tiny-tim said:
hi steveandy2002! :smile:

(try using the X2 button just above the Reply box :wink:)


s = 100, u = 72, a = 10 …

what's the difficulty? :confused:


not sure what you mean, i need to get time not s
 
All you need to do is plug in your known values into s=ut+\frac{1}{2}gt2. Then you move everything to one side and solve the quadratic equation. What are you having issues with?
 
Don't forget to change the units on u from km/hr to m/s.
 
Thread 'Voltmeter readings for this circuit with switches'
TL;DR Summary: I would like to know the voltmeter readings on the two resistors separately in the picture in the following cases , When one of the keys is closed When both of them are opened (Knowing that the battery has negligible internal resistance) My thoughts for the first case , one of them must be 12 volt while the other is 0 The second case we'll I think both voltmeter readings should be 12 volt since they are both parallel to the battery and they involve the key within what the...
Thread 'Correct statement about a reservoir with an outlet pipe'
The answer to this question is statements (ii) and (iv) are correct. (i) This is FALSE because the speed of water in the tap is greater than speed at the water surface (ii) I don't even understand this statement. What does the "seal" part have to do with water flowing out? Won't the water still flow out through the tap until the tank is empty whether the reservoir is sealed or not? (iii) In my opinion, this statement would be correct. Increasing the gravitational potential energy of the...
Back
Top